Dwyer USA Mark II Plastic Manometer Wholesaler

DWYER OMEGA / MAGNEHELIC DIFFERENTIAL PRESSURE GAUGE NEAR Huda Industrial Area Ballabgarh Haryana

DWYER OMEGA / MAGNEHELIC DIFFERENTIAL PRESSURE GAUGE NEAR Huda Industrial Area Ballabgarh Haryana

SERIES 2000 MAGNEHELIC® DIFFERENTIAL PRESSURE GAGES Indicate Positive, Negative or Differential, Accurate within 1%

No Power Required
Low Cost
Used in Isolation/ Hospital Environments and Temporary Units (no Power Required)

Select the Series 2000 Magnehelic® Gage for a versatile low Differential Pressure Gage With a Wide Choice of 81 Models and 27 Options To Choose From. Using Dwyer’s Simple, frictionless Magnehelic® Gage movement, it quickly indicates air or noncorrosive gas pressures–either positive, negative (vacuum) or differential. The design resists shock, vibration, over-pressures and is weatherproof to IP67. Select the -HA High Accuracy Magnehelic® Gage option for an accuracy within 1% of full scale, located below in the Product Configurator. Also included with the –HA option at no extra cost are a mirrored scale overlay and a 6 point calibration certificate.

NIST CALIBRATION available in Product Configurator.

Note: May be used with Hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi.

Please see Series AT-2000 for ATEX approved.

California Residents: Click Here for Proposition 65 WARNING.

PRODUCT APPLICATIONS

Filter Monitoring
Air Velocity with Dwyer Pitot Tube
Blower Vacuum Monitoring
Fan Pressure Indication
Duct, Room or Building Pressures
Clean Room Positive Pressure Indication

Model	Description
2000-1.5KPA	Magnehelic Differential Pressure Gage, Range 0-1.5 kPa, minor divisions .05.
2000-10KPA	Magnehelic Differential Pressure Gage, Range 0-10 kPa, minor divisions .20.
2000-15KPA	Magnehelic Differential Pressure Gage, Range 0-15 kPa, minor divisions .50.
2000-1KPA	Magnehelic Differential Pressure Gage, Range 0-1 kPa, minor divisions .02.
2000-20KPA	Magnehelic Differential Pressure Gage, Range 0-20 kPa, minor divisions .50.
2000-25KPA	Magnehelic Differential Pressure Gage, Range 0-25 kPa, minor divisions .50.
2000-2KPA	Magnehelic Differential Pressure Gage, Range 0-2 kPa, minor divisions .05.
2000-30KPA	Magnehelic Differential Pressure Gage, Range 0-30 kPa, minor divisions 1.0.
2000-3KPA	Magnehelic Differential Pressure Gage, Range 0-3 kPa, minor divisions .10.
2000-4KPA	Magnehelic Differential Pressure Gage, Range 0-4 kPa, minor divisions .10.
2000-5KPA	Magnehelic Differential Pressure Gage, Range 0-5 kPa, minor divisions .10.
2000-8KPA	Magnehelic Differential Pressure Gage, Range 0-8 kPa, minor divisions .20.
2300-1KPA	Magnehelic Differential Pressure Gage, Range 0.5-0-0.5 kPa, minor divisions .02.
2300-3KPA	Magnehelic Differential Pressure Gage, Range 1.5-0-1.5 kPa, minor divisions .10.

Additional Information:

Item Code: DWYER OMEGA / MAGNEHELIC DIFFERENTIAL PRESSURE GAUGE NEAR Huda Industrial Area Ballabgarh Haryana
WhatsApp No.9871034100,9868958924,9650264867,9716640145,8368866030,8368801023
www.envirotechindustrialproducts.net
www.envirotechindustrialproduct.net
www.envirotechindustrialproductsindia.in
www.envirotechindustrialproductsdelhi.com
www.envirotechindustrialproduct.info
www.envirotechindustrialproducts.info
www.envirotechdelhi.com
www.envirotechindia.co.in

CATEGORY Leder Dwyer : Magnehelic Differential Pressure Gauge, CATEGORY LEDER DWYER Magnehelic Differential Pressure Gauge ALL INDIA, DWYER DIFFERENTIAL PRESSURE Gauge Dealers Delhi, Dwyer Differential Pressure Switch Wholesaler, Dwyer Distributor Envirotech Industrial India, Dwyer Distributors India, Dwyer Fittings Accessories, Dwyer Instruments, Dwyer Instruments Distributors Delhi, Dwyer Instruments Distributors in Delhi, Dwyer Instruments Distributors in India, Dwyer Instruments Distributors Wholesaler In India, Dwyer Instruments, Dwyer Instruments Distributors Delhi, Dwyer Magnehelic Gauge Wholesale Suppliers India, Dwyer Pressure Gauge Wholesaler In INDIA, Dwyer Pressure Gauge Wholesaler In INDIA, Dwyer Products INDIA DELHI, Dwyer Products INDIA DELHI, Dwyer Stainless Steel Pitot Tube Wholesalers, Dwyer Usa Magnehelic Gauge Wholesale Noida, Dwyer USA Mark II Plastic Manometer Wholesaler, Mounting Options Dwyer Instruments, PREMIUM SELLER DWYER : MAGNEHELIC DIFFERENTIAL PRESSURE GAUGE ALL INDIA, PREMIUM SELLER DWYER / MAGNEHELIC DIFFERENTIAL PRESSURE GAUGE All India, SUPER SELLER DWYER : MAGNEHELIC DIFFERENTIAL PRESSURE GAUGE, SUPER SELLER DWYER / MAGNEHELIC DIFFERENTIAL PRESSURE GAUGE All India, TRUSTED SELLER DWYER : MAGNEHELIC DIFFERENTIAL PRESSURE GAUGE ALL INDIA, TRUSTED SELLER DWYER / MAGNEHELIC DIFFERENTIAL PRESSURE GAUGE ALL INDIA

Magnehelic / Differential Pressure Gauge In Kotda Sangani Industrial Area Rajkot Gujarat

Magnehelic / Differential Pressure Gauge In Kotda Sangani Industrial Area Rajkot Gujarat

SERIES 2000 MAGNEHELIC® DIFFERENTIAL PRESSURE GAGES Indicate Positive, Negative or Differential, Accurate within 1%

No Power Required
Low Cost
Used in Isolation/ Hospital Environments and Temporary Units (No Power Required)

Select The Series 2000 Magnehelic® Gage for a Versatile Low Differential Pressure Gage With a Wide Choice Of 81 Models And 27 Options To Choose From. Using Dwyer’s simple, frictionless Magnehelic® Gage movement, it quickly indicates air or noncorrosive gas pressures–either positive, negative (vacuum) or differential. The design resists shock, vibration, over-pressures and is weatherproof to IP67. Select the -HA High Accuracy Magnehelic® Gage option for an accuracy within 1% of full scale, located below in the Product Configurator. Also included with the –HA option at no extra cost are a mirrored scale overlay and a 6 point calibration certificate.

NIST CALIBRATION available in Product Configurator.

Note: May be used with Hydrogen. Order a Buna-N diaphragm. Pressures must be less than 35 psi.

Please see Series AT-2000 for ATEX approved.

California Residents: Click Here for Proposition 65 WARNING.

PRODUCT APPLICATIONS

Filter Monitoring
Air Velocity with Dwyer Pitot Tube
Blower Vacuum Monitoring
Fan Pressure Indication
Duct, Room or Building Pressures
Clean Room Positive Pressure Indication

Model	Description
2000-1.5KPA	Magnehelic Differential Pressure Gage, Range 0-1.5 kPa, minor divisions .05.
2000-10KPA	Magnehelic Differential Pressure Gage, Range 0-10 kPa, minor divisions .20.
2000-15KPA	Magnehelic Differential Pressure Gage, Range 0-15 kPa, minor divisions .50.
2000-1KPA	Magnehelic Differential Pressure Gage, Range 0-1 kPa, minor divisions .02.
2000-20KPA	Magnehelic Differential Pressure Gage, Range 0-20 kPa, minor divisions .50.
2000-25KPA	Magnehelic Differential Pressure Gage, Range 0-25 kPa, minor divisions .50.
2000-2KPA	Magnehelic Differential Pressure Gage, Range 0-2 kPa, minor divisions .05.
2000-30KPA	Magnehelic Differential Pressure Gage, Range 0-30 kPa, minor divisions 1.0.
2000-3KPA	Magnehelic Differential Pressure Gage, Range 0-3 kPa, minor divisions .10.
2000-4KPA	Magnehelic Differential Pressure Gage, Range 0-4 kPa, minor divisions .10.
2000-5KPA	Magnehelic Differential Pressure Gage, Range 0-5 kPa, minor divisions .10.
2000-8KPA	Magnehelic Differential Pressure Gage, Range 0-8 kPa, minor divisions .20.
2300-1KPA	Magnehelic Differential Pressure Gage, Range 0.5-0-0.5 kPa, minor divisions .02.
2300-3KPA	Magnehelic Differential Pressure Gage, Range 1.5-0-1.5 kPa, minor divisions .10.

Additional Information:

Item Code: Magnehelic : Differential Pressure Gauge In Kotda Sangani Industrial Area Rajkot Gujarat
WhatsApp No.9871034100,9868958924,9650264867,9716640145,8368866030,8368801023
www.envirotechindustrialproducts.co.in
www.envirotechindustrialproduct.co.in
www.envirotechindustrialproduct.in
www.envirotechindustrialproducts.in
www.envirotechindustrialproduct.com
www.envirotechindustrialproducts.com
www.envirotechindustrialproducts.net

Dwyer USA Mark II Plastic Manometer Wholesaler, Uncategorized

Dwyer USA Mark II Plastic Manometer Wholesaler

Nov 3, 2021 by admin 0 Comments

Mark II Model 40-1-AV Dwyer Manometer Range 0-1.1 Inches w.c

Material	Molded Plastic
Accuracy	+-3% FS
Model Name/Number	MARK II MODEL 40-1-AV MANOMETER
Brand	Dwyer USA
Scale Length	Approx. 8-1/4″ (21 cm)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Weight	1.04 lb (472 g)/1.23 lb (558 g)

Mark II Model 40-1-AV Dwyer Manometer Range 0-1.1 Inches w.c
Dwyer Mark II Series Molded Manometers are of the inclined and inclined-vertical types. The Model 40 inclined gage provides linear calibration and excellent resolution throughout its range. Also, it is ideally suited for air velocity and air filter gage applications. Capable of pressure measurements above and below atmospheric as well as differential pressure measurements.

Construction:

Mark II Manometers are economically priced, compact and available in both stationary and portable configurations. The portable stand is a standard feature on Model 40. Construction is simple with virtually indestructible molded white styrene-acrylonitrile housing, indicating tube and fluid wells, molded ABS knobs and zero adjust plunger, shock mounted glass level vial and leak proof “O” ring seals. Greater protection is provided by float operated overflow traps in the Model 40. Scales are lithograph printed on aluminum and epoxy coated.

Installation:

Mark II Manometers can be mounted on any vertical surface with the two mounting screws provided. A built-in spirit level simplifies leveling before mounting screws are tightened. Simply fill the reservoir, adjust fluid level to zero, connect the tubing, and the gage is ready for operation.

Accessories:
Included with each Mark II Manometer are two tubing connectors for 1/8″ pipe or sheet metal ducts, two mounting screws, 3/4 ounce bottle of indicating fluid, red and green pointer flags and complete instructions. The Model 40 contains two 4-1/2 foot lengths of clear plastic tubing, a plastic swing-out stand and leveling screw for portable operation. It also features convenient rapid shutoff pressure connections and integral overpressure safety traps.

Below are other pressure ranges available for Series Mark II Manometer:

Model	Range	Fluid Used
Mark II 40-1	.1-0-1.0 in w.c.	Red oil, .826 s.g.
Mark II 40-25mm	0-26 mm w.c	Red oil, .826 s.g.
Mark II 40-250PA	10-0-250 Pa	Red oil, .826 s.g.
Mark II 41-2	.2-0-2.4 in w.c.	Blue oil, 1.91 s.g.
Mark II 41-60mm	0-60 mm w.c.	Blue oil, 1.91 s.g.
Mark II 41-600PA	20-0-600 Pa	Blue oil, 1.91 s.g.
Mark II 40-1-AV*	0-1.1 in w.c. & 0-4200 fpm	Red oil, .826 s.g.
Mark II 40-250PA-AV*	0-260 Pa & 0-21 mps	Red oil, .826 s.g.
Mark II 41-2-AV*	0-2.5 in wc. & 0-6300 fpm	Blue oil, 1.91 s.g.

Mark II Model 40-1 Dwyer Manometer Range .1-0-1.0 Inches W.C

Material	Molded Plastic
Accuracy	+-3% FS
Usage/Application	Air Filter Gage
Brand	Dwyer
Model Name/Number	MARK II MODEL 40-1
Scale Length	Approx. 8-1/4″ (21 cm)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Weight	1.04 lb (472 g)/1.23 lb (558 g)

Mark II Model 40-1 Dwyer Manometer Range .1-0-1.0 Inches w.c Dwyer Mark II Series Molded Manometers are of the inclined and inclined-vertical types. The Model 40 inclined gage provides linear calibration and excellent resolution throughout its range. Also, it is ideally suited for Air Velocity and Air Filter Gage Applications. Capable of pressure measurements above and below atmospheric as well as Differential Pressure Measurements.

Construction:

Mark II Manometers are economically priced, compact and available in both stationary and portable configurations. The portable stand is a standard feature on Model 40. Construction is simple with virtually indestructible molded white styrene-acrylonitrile housing, indicating tube and fluid wells, molded ABS knobs and zero adjust plunger, shock mounted glass level vial and leak proof “O” ring seals. Greater protection is provided by float operated overflow traps in the Model 40. Scales are lithograph printed on aluminum and epoxy coated.

Installation:

Mark II Manometers can be mounted on any vertical surface with the two mounting screws provided. A built-in spirit level simplifies leveling before mounting screws are tightened. Simply fill the reservoir, adjust fluid level to zero, connect the tubing, and the gage is ready for operation.

Accessories:

Included with each
Mark II Manometer
are two tubing connectors for 1/8″ pipe or sheet metal ducts, two mounting screws, 3/4 ounce bottle of indicating fluid, red and green pointer flags and complete instructions. The Model 40 contains two 4-1/2 foot lengths of clear plastic tubing, a plastic swing-out stand and leveling screw for portable operation. It also features convenient rapid shutoff pressure connections and integral overpressure safety traps.

Below are other pressure ranges available for Series Mark II Manometer:

Model	Range	Fluid Used
Mark II 40-1	.1-0-1.0 in w.c.	Red oil, .826 s.g.
Mark II 40-25mm	0-26 mm w.c	Red oil, .826 s.g.
Mark II 40-250PA	10-0-250 Pa	Red oil, .826 s.g.
Mark II 41-2	.2-0-2.4 in w.c.	Blue oil, 1.91 s.g.
Mark II 41-60mm	0-60 mm w.c.	Blue oil, 1.91 s.g.
Mark II 41-600PA	20-0-600 Pa	Blue oil, 1.91 s.g.
Mark II 40-1-AV*	0-1.1 in w.c. & 0-4200 fpm	Red oil, .826 s.g.
Mark II 40-250PA-AV*	0-260 Pa & 0-21 mps	Red oil, .826 s.g.
Mark II 41-2-AV*	0-2.5 in wc. & 0-6300 fpm	Blue oil, 1.91 s.g.

Mark II Model 28 Dwyer Manometer Range 0-10,500 FPM

Minimum Order Quantity	1 Number
Model Name/Number	MARK II MODEL 28
Usage/Application	Laboratory
Accuracy	+-3% FS
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Material	Molded Plastic
Brand	Dwyer
Scale Length	Approx. 8-1/4″ (21 cm
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)

Mark II Model 28 Dwyer Manometer Range 0-10,500 fpm Dwyer Mark II Series Molded Manometers are of the inclined and inclined-vertical types. The curved inclined-vertical tube of the Model 25 gage provides higher ranges with more easily read increments at low readings. The Model 25 is excellent for general purpose work. Capable of pressure measurements above and below atmospheric as well as differential pressure measurements.

Construction:

Mark II Manometers are economically priced, compact and available in both stationary and portable configurations, optional A-612 stand for Model 25. Construction is simple with virtually indestructible molded white styrene-acrylonitrile housing, indicating tube and fluid wells, molded ABS knobs and zero adjust plunger, shock mounted glass level vial and leak proof “O” ring seals. Moderate overpressures are accommodated by an overflow tank. Scales are lithograph printed on aluminum and epoxy coated.

Installation:

Mark II Manometers can be mounted on any vertical surface with the two mounting screws provided. A built-in spirit level simplifies leveling before mounting screws are tightened. Simply fill the reservoir, adjust fluid level to zero, connect the tubing, and the gage is ready for operation.

Accessories:

Included with each Mark II Manometer are two tubing connectors for 1/8″ pipe or sheet metal ducts, two mounting screws, 3/4 ounce bottle of indicating fluid, red and green pointer flags and complete instructions. The Model 25 also includes 8 feet of flexible double column plastic tubing. Portable operation is made possible by the use of the optional A-612 portable stand. A short piece of tubing can be slipped over the pressure connections to contain the gage oil in transit.

Below are other pressure ranges available for Series Mark II Manometer:

Model	Range	Fluid Used
Mark II 25	0-3 in w.c.	Red oil, .826 s.g.
Mark II 26	0-7 in w.c.	Blue oil, 1.91 s.g.
Mark II 27*	0-7000 fpm	Red oil, .826 s.g.
Mark II 28*	0-10,500 fpm	Blue oil, 1.91 s.g.
Mark II MM-80	0-80 mm w.c.	Red oil, .826 s.g.
Mark II MM-180	0-180 mm w.c.	Blue oil, 1.91 s.g.
Mark II M-700PA	10-0-700 Pa	Red oil, .826 s.g.

Mark II Model 27 Dwyer Manometer Range 0-7000 FPM

Material	Molded Plastic
Accuracy	+-3% FS
Usage/Application	Air Filter Gage
Brand	Dwyer
Model Name/Number	MARK II MODEL 27
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Scale Length	Approx. 8-1/4″ (21 cm).

Mark II Model 27 Dwyer Manometer Range 0-7000 fpm Dwyer Mark II Series Molded Manometers are of the inclined and inclined-vertical types. The curved inclined-vertical tube of the Model 25 gage provides higher ranges with more easily read increments at low readings. The Model 25 is excellent for general purpose work. Capable of pressure measurements above and below atmospheric as well as differential pressure measurements.

Construction:

Mark II Manometers are economically priced, compact and available in both stationary and portable configurations, optional A-612 stand for Model 25. Construction is simple with virtually indestructible molded white styrene-acrylonitrile housing, indicating tube and fluid wells, molded ABS knobs and zero adjust plunger, shock mounted glass level vial and leak proof “O” ring seals. Moderate overpressures are accommodated by an overflow tank. Scales are lithograph printed on aluminum and epoxy coated.

Installation

Mark II Manometers can be mounted on any vertical surface with the two mounting screws provided. A built-in spirit level simplifies leveling before mounting screws are tightened. Simply fill the reservoir, adjust fluid level to zero, connect the tubing, and the gage is ready for operation.

Accessories

Included with each Mark II Manometer are two tubing connectors for 1/8″ pipe or sheet metal ducts, two mounting screws, 3/4 ounce bottle of indicating fluid, red and green pointer flags and complete instructions. The Model 25 also includes 8 feet of flexible double column plastic tubing. Portable operation is made possible by the use of the optional A-612 portable stand. A short piece of tubing can be slipped over the pressure connections to contain the gage oil in transit.

Below are other pressure ranges available for Series Mark II Manometer:

Model	Range	Fluid Used
Mark II 25	0-3 in w.c.	Red oil, .826 s.g.
Mark II 26	0-7 in w.c.	Blue oil, 1.91 s.g.
Mark II 27*	0-7000 fpm	Red oil, .826 s.g.
Mark II 28*	0-10,500 fpm	Blue oil, 1.91 s.g.
Mark II MM-80	0-80 mm w.c.	Red oil, .826 s.g.
Mark II MM-180	0-180 mm w.c.	Blue oil, 1.91 s.g.
Mark II M-700PA	10-0-700 Pa	Red oil, .826 s.g.

Mark II Model 26 Dwyer Manometer Range 0-7 Inches WC

Material	Molded Plastic
Accuracy	+-3% FS
Usage/Application	Air Velocity Measurement
Brand	Dwyer
Model Name/Number	MARK II MODEL 26
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Scale Length	Approx. 8-1/4″ (21 cm)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)

Mark II Model 26 Dwyer Manometer Range 0-7 Inches WC Dwyer Mark II series molded manometers are of the inclined and inclined-vertical types. The curved inclined-vertical tube of the Model 25 gage provides higher ranges with more easily read increments at low readings. The Model 25 is excellent for general purpose work. Capable of pressure measurements above and below atmospheric as well as differential pressure measurements.

Construction

Mark II manometers

are economically priced, compact and available in both stationary and portable configurations, optional A-612 stand for Model 25. Construction is simple with virtually indestructible molded white styrene-acrylonitrile housing, indicating tube and fluid wells, molded ABS knobs and zero adjust plunger, shock mounted glass level vial and leak proof “O” ring seals. Moderate overpressures are accommodated by an overflow tank. Scales are lithograph printed on aluminum and epoxy coated.

Installation:

Mark II manometers can be mounted on any vertical surface with the two mounting screws provided. A built-in spirit level simplifies leveling before mounting screws are tightened. Simply fill the reservoir, adjust fluid level to zero, connect the tubing, and the gage is ready for operation.

Accessories:

Included with each Mark II manometer are two tubing connectors for 1/8″ pipe or sheet metal ducts, two mounting screws, 3/4 ounce bottle of indicating fluid, red and green pointer flags and complete instructions. The Model 25 also includes 8 feet of flexible double column plastic tubing. Portable operation is made possible by the use of the optional A-612 portable stand. A short piece of tubing can be slipped over the pressure connections to contain the gage oil in transit.

Below Are Other Pressure Ranges Available For Series Mark II Manometer:

Model	Range	Fluid Used
Mark II 25	0-3 in w.c.	Red oil, .826 s.g.
Mark II 26	0-7 in w.c.	Blue oil, 1.91 s.g.
Mark II 27*	0-7000 fpm	Red oil, .826 s.g.
Mark II 28*	0-10,500 fpm	Blue oil, 1.91 s.g.
Mark II MM-80	0-80 mm w.c.	Red oil, .826 s.g.
Mark II MM-180	0-180 mm w.c.	Blue oil, 1.91 s.g.
Mark II M-700PA	10-0-700 Pa	Red oil, .826 s.g.

Mark II Model 25 Dwyer Manometer Range 0-3 Inches WC

Material	Molded Plastic
Usage/Application	Air Velocity Measurement
Accuracy	+-3% FS
Model Name/Number	MARK II 25 SERIES MARK II
Brand	Dwyer USA
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Size	Approx 8-1/4 INCH 21 cm
I Deal In	New Only
Scale Length	Approx. 8-1/4″ (21 cm)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)

Mark II Model 25 Dwyer Manometer Range 0-3 Inches WC Dwyer Mark II Series Molded Manometers are of the inclined and inclined-Vertical Types. The Curved Inclined-Vertical Tube of the Model 25 Gage provides higher ranges with more easily read increments at low readings. The Model 25 is excellent for general purpose work. Capable of pressure measurements above and below atmospheric as well as Differential Pressure Measurements.

Construction:

Mark II Manometers are economically priced, compact and available in both stationary and portable configurations, optional A-612 stand for Model 25. Construction is simple with virtually indestructible molded white styrene-acrylonitrile housing, indicating tube and fluid wells, molded ABS knobs and zero adjust plunger, shock mounted glass level vial and leak proof “O” ring seals. Moderate overpressures are accommodated by an overflow tank. Scales are lithograph printed on aluminum and epoxy coated.

Installation:

Mark II Manometers can be mounted on any vertical surface with the two mounting screws provided. A built-in spirit level simplifies leveling before mounting screws are tightened. Simply fill the reservoir, adjust fluid level to zero, connect the tubing, and the gage is ready for operation.

Accessories:

Included with each Mark II Manometer are two tubing connectors for 1/8″ pipe or sheet metal ducts, two mounting screws, 3/4 ounce bottle of indicating fluid, red and green pointer flags and complete instructions. The Model 25 also includes 8 feet of flexible double column plastic tubing. Portable operation is made possible by the use of the optional A-612 portable stand. A short piece of tubing can be slipped over the pressure connections to contain the gage oil in transit.

Below Are Other Pressure Ranges Available For Series Mark II Manometer:

Model	Range	Fluid Used
Mark II 25	0-3 in w.c.	Red oil, .826 s.g.
Mark II 26	0-7 in w.c.	Blue oil, 1.91 s.g.
Mark II 27*	0-7000 fpm	Red oil, .826 s.g.
Mark II 28*	0-10,500 fpm	Blue oil, 1.91 s.g.
Mark II MM-80	0-80 mm w.c.	Red oil, .826 s.g.
Mark II MM-180	0-180 mm w.c.	Blue oil, 1.91 s.g.
Mark II M-700PA	10-0-700 Pa	Red oil, .826 s.g.

Mark II Dwyer Molded Plastic Manometer

Minimum Order Quantity	1 Number
Material	Molded Plastic
Accuracy	+-3% FS
Usage/Application	Paint Booths
Brand	Dwyer
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Size	Approx 8-1/4 INCH 21 cm
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Scale Length	Approx. 8-1/4″ (21 cm)

Mark II Dwyer Molded Plastic Manometer Series Mark Iimolded Manometers are of the inclined and inclined-vertical types. The curved inclined-vertical tube of the Model 25 gage provides higher ranges with more easily read increments at low readings. The Model 25 is excellent for general purpose work. The Model 40 inclined gage provides linear calibration and excellent resolution throughout its range. The Model 40 is ideally suited for air velocity and Air Filter Gage applications. Both Gage types are capable of pressure measurements above and below atmospheric as well as differential pressure measurements. Included with each Mark II Manometer are two tubing connectors for 1/8″ pipe or sheet metal ducts, two mounting screws, 1 ounce bottle of indicating fluid, red and green pointer flags and complete instructions. The Model 25 also includes 8′ of flexible double column plastic tubing. Portable operation of the Model 25 is made possible by the use of the optional A-612 portable stand. A short piece of tubing can be slipped over the Model 25 pressure connections to contain the gage fluid in transit. The Model 40 contains two 4-1/2′ lengths of clear plastic tubing, a plastic swing-out stand and leveling screw for portable operation. It also features convenient rapid shutoff pressure connections and integral overpressure safety traps. Click here, if you require a Safety Data Sheet for the Blue Gage Fluid or the Red Gage Fluid.

Product Applications:

Paint Booths
Air Velocity Measurement
Air Filter Gage

Models & Ordering:

Model	Description
MARK II 25	Molded Plastic Manometer, Range 0-3″ w.c., Red Oil, .826 sp. gr.
MARK II 26	Molded Plastic Manometer,Rrange 0-7″ w.c., Blue Oil, 1.91 sp. gr.
MARK II 27	Molded Plastic Manometer, Range 0-7000 fpm, Red Oil, .826 sp. gr., Requires Pitot Tube *Sold Separately.
MARK II 28	Molded Plastic Manometer, Range 0-10,500 fpm, Blue Oil, 1.91 sp. gr., Requires Pitot Tube *Sold Separately.
MARK II 40-1	Molded Plastic Manometer, Range .1-0-1.0″ w.c., Red Oil, .826 sp. gr.
MARK II 40-1-AV	Molded Plastic Manometer, Range 0-1.1″ w.c. & 0-4200 FPM, Red Oil, .826 sp. gr., Requires Pitot Tube Sold Separately.
MARK II 40-250PA	Molded Plastic Manometer, Range 10-0-250 Pa, Red Oil, .826 sp. gr.
MARK II 40-250PA-AV	Molded Plastic Manometer, Range 0-260 Pa & 0-21 MPS, Red Oil, .826 sp. gr., Requires Pitot Tube Sold Separately.
MARK II 40-25MM	Molded Plastic Manometer, Range 0-26 mm w.c., Red Oil, .826 sp. gr.
MARK II 41-2	Molded Plastic Manometer, Range .2-0-2.4″ w.c., Blue Oil, 1.91 sp. gr.
MARK II 41-2-AV	Molded Plastic Manometer, Range 0-2.5″ w.c. & 0-6300 FPM, Blue Oil, 1.91 sp. gr., Requires Pitot Tube Sold Separately.
MARK II 41-600PA	Molded Plastic Manometer, Range 20-0-600 Pa, Blue Oil, 1.91 sp. gr.
MARK II 41-60MM	Molded Plastic Manometer, Range 0-60 MM W.C., Blue Oil, 1.91 sp. gr.
MARK II M-700PA	Molded Plastic Manometer, Range 10-0-700 Pa, Red Oil, .826 sp. gr.
MARK II MM-180	Molded Plastic Manometer, Range 0-180 MM W.C., Blue Oil, 1.91 sp. gr.
MARK II MM-80	Molded Plastic Manometer, Range 0-80 MM W.C., Red Oil, .826 sp. gr.

Mark II Model 40-250PA Dwyer Manometer Range 10-0-250 Pa

Material	Molded Plastic
Accuracy	+-3% FS
Usage/Application	Paint Booths
Brand	Dwyer
Model Name/Number	MARK II MODEL 40-250PA
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Scale Length	Approx. 8-1/4″ (21 cm)

Mark II Model 40-250PA Dwyer Manometer Range 10-0-250 Pa Dwyer Mark II Series Molded Manometers are of the inclined and inclined-vertical types. The Model 40 inclined gage provides linear calibration and excellent resolution throughout its range. Also, it is ideally suited for air velocity and air filter gage applications. Capable of pressure measurements above and below atmospheric as well as differential pressure measurements.

Construction

Mark II Manometers are economically priced, compact and available in both stationary and portable configurations. The portable stand is a standard feature on Model 40. Construction is simple with virtually indestructible molded white styrene-acrylonitrile housing, indicating tube and fluid wells, molded ABS knobs and zero adjust plunger, shock mounted glass level vial and leak proof “O” ring seals. Greater protection is provided by float operated overflow traps in the Model 40. Scales are lithograph printed on aluminum and epoxy coated.

Installation:

Mark II Manometers can be mounted on any vertical surface with the two mounting screws provided. A built-in spirit level simplifies leveling before mounting screws are tightened. Simply fill the reservoir, adjust fluid level to zero, connect the tubing, and the gage is ready for operation.

Accessories

Included with each

Mark II Manometer are two tubing connectors for 1/8″ pipe or sheet metal ducts, two mounting screws, 3/4 ounce bottle of indicating fluid, red and green pointer flags and complete instructions. The Model 40 contains two 4-1/2 foot lengths of clear plastic tubing, a plastic swing-out stand and leveling screw for portable operation. It also features convenient rapid shutoff pressure connections and integral overpressure safety traps.

Below are other pressure ranges available for Series Mark II Manometer:

Model	Range	Fluid Used
Mark II 40-1	.1-0-1.0 in w.c.	Red oil, .826 s.g.
Mark II 40-25mm	0-26 mm w.c	Red oil, .826 s.g.
Mark II 40-250PA	10-0-250 Pa	Red oil, .826 s.g.
Mark II 41-2	.2-0-2.4 in w.c.	Blue oil, 1.91 s.g.
Mark II 41-60mm	0-60 mm w.c.	Blue oil, 1.91 s.g.
Mark II 41-600PA	20-0-600 Pa	Blue oil, 1.91 s.g.
Mark II 40-1-AV*	0-1.1 in w.c. & 0-4200 fpm	Red oil, .826 s.g.
Mark II 40-250PA-AV*	0-260 Pa & 0-21 mps	Red oil, .826 s.g.
Mark II 41-2-AV*	0-2.5 in wc. & 0-6300 fpm	Blue oil, 1.91 s.g.

Mark II Model 40-250PA-AV Dwyer Manometer Range 0-250 Pa,0-21 mps

Minimum Order Quantity	1 Number
Material	Molded Plastic
Accuracy	+-3% FS
Model Name/Number	MARK II MODEL 40-250PA-AV
Brand	Dwyer USA
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Scale Length	Approx. 8-1/4″ (21 cm)

Mark II Model 40-250PA-AV Dwyer Manometer Range 0-250 Pa,0-21 mps
Dwyer A-489 SS Straight Static Pressure Tip With Flange, 4″ (101 MM) Insertion Depth

Key Features:

Rapid Shutoff Pressure Connections and Integral Overpressure Safety Traps
Requires Pitot Tube, Not Included

Applications:

Air Velocity
Air Filter Guge

Other Details:

The Dwyer MARKII40250PAAV Molded Plastic Inclined Manometer, 0-260 Pa, 0-21 mps, Red Gauge Fluid, Requires Pitot Tube Provides Linear Calibration and Excellent Resolution Throughout its Range. This model is capable of pressure measurements above and below atmospheric as well as differential pressure measurements. The MARK II 40-250PA-AV includes accessories to enable portable use of the unit.

Included:

2 – Tubing connectors for 1/8 in. pipe or sheet metal ducts
2 – Mounting screws
2 – 4-1/2” lengths of clear plastic tubing
1 – Plastic swing-out stand
1 – Leveling screw
1 – 1 ounce bottle of indicating fluid
1 – Set of red and green pointer flags
1 – User Manual

Mark II Model 40-25MM Dwyer Manometer Range 0-26 MM W.C

Material	Molded Plastic
Accuracy	+-3% FS
Usage/Application	Paint Booths
Brand	Dwyer
Model Name/Number	MARK II MODEL 40-25MM
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)

Mark II Model 40-25MM Dwyer Manometer Range 0-26 MM W.C Dwyer A-489 SS Straight Static Pressure Tip With Flange, 4″ (101 MM) Insertion Depth

Key Features:

Rapid Shutoff Pressure Connections and Integral Overpressure Safety Traps
Requires Pitot Tube, Not Included

Applications:

Air Velocity
Air Filter Guge

Other Details:

The Dwyer MARKII40255MM Molded Plastic Inclined Manometer, 0-26 mm w.c., Red Gauge Fluid Provides linear Calibration and Excellent Resolution Throughout its Range. This model is capable of pressure Measurements above and below Atmospheric as well as Differential Pressure Measurements. The MARK II 40-255MM includes Accessories to Enable Portable Use of The Unit

Included:

2 – Tubing connectors for 1/8 in. Pipe or Sheet Metal Ducts
2 – Mounting Screws
2 – 4-1/2” lengths of clear plastic Tubing
1 – Plastic Swing-Out Stand
1 – Leveling Screw
1 – 1 ounce bottle of indicating fluid
1 – Set of red and green pointer flags
1 – User Manual

Mark II Model 41-2 Dwyer Manometer Range .2-0-2.4 Inches

Material	Molded Plastic
Accuracy	+-3% FS
Usage/Application	Air Velocity Measurement
Model Name/Number	MARK II MODEL 41-2
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Scale Length	Approx. 8-1/4″ (21 cm)

Mark II Model 41-2 Dwyer Manometer Range .2-0-2.4 Inches Dwyer A-489 SS Straight Static Pressure Tip With Flange, 4″ (101 MM) Insertion Depth

Key Features:

Rapid Shutoff Pressure Connections and Integral Overpressure Safety Traps
Requires Pitot Tube, Not Included

Applications:

Air Velocity
Air Filter Guge

Other Details:

The Dwyer MARKII412 Molded Plastic Inclined Manometer, .2-0-2.4 INCHES., Blue Gauge Fluid Provides linear Calibration and Excellent Resolution Throughout its Range. This model is capable of pressure Measurements above and below Atmospheric as well as Differential Pressure Measurements. The MARK II 412 includes Accessories to Enable Portable Use of The Unit

Included:

2 – Tubing connectors for 1/8 in. Pipe or Sheet Metal Ducts
2 – Mounting Screws
2 – 4-1/2” lengths of clear plastic Tubing
1 – Plastic Swing-Out Stand
1 – Leveling Screw
1 – 1 ounce bottle of indicating fluid
1 – Set of red and green pointer flags
1 – User Manual

Mark II Model 41-2-AV Dwyer Manometer 0-2.5 inch W.C

Material	Molded Plastic
Accuracy	+-3% FS
Usage/Application	Paint Booths
Brand	Dwyer
Model Name/Number	MARK II MODEL 41-2-AV
Scale Length	Approx. 8-1/4″ (21 cm)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Weight	1.04 lb (472 g)/1.23 lb (558 g)

Mark II Model 41-2-AV Dwyer Manometer 0-2.5 inch w.c The Dwyer Mark II Series provides linear calibration and excellent resolution throughout its range and is ideally suited for air velocity and air filter gage Applications.

Mark II Model 41-600PA Dwyer Manometer 20-0-600 Pa

Minimum Order Quantity	1 Number
Material	Molded Plastic
Accuracy	+-3% FS
Usage/Application	Paint Booths
Brand	Dwyer
Model Name/Number	MARK II MODEL 41-600PA
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Scale Length	Approx. 8-1/4″ (21 cm)

Mark II Model 41-600PA Dwyer Manometer 20-0-600 Pa

Dwyer MARK II 41-600PA Inclined Manometer (20-0-600 Pa) using Blue Gauge Fluid
Model: MARK II 41-600PA | Order No: 41-600PA

Designed to Give Fast, Accurate Indication of Differential Pressures. The Gage May be used as a Readout device when measuring flowing fluids, pressure drop across filters, liquid levels in storage tanks and many other applications involving pressure.

Dwyer 41-600pa Manometer, Air Filter Gauge, 0-1

There are no moving parts – no mechanical linkages – nothing to wear out, jam or deteriorate from vibration.
They never need calibration.
2 psi max. Pressure.
The mirror polished inclined scale allows the operator to easily read minute differences in differential pressure across the filter accurately without parallax error.
Over pressure safety traps

Specifications:

For Architects and Engineers
An Air Filter Gage for measuring the resistance to Air Flow through the filters shall be installed, one for each bank of filters. The gage shall be of inclined tube Differential Type (equipped with vent valves for zeroing) shall be of solid acrylic plastic construction with built-in level vial, shall have an adjustable mirror-polished scale, shall be furnished complete with two 5-foot lengths 1/4″ tubing, two static pressure tips, mounting hardware, additional bottle of Red Gage oil and instructions.

What”s Included With The Dwyer MARK II 41-600PA

Dwyer MARK II 41-600PA Inclined Manometer (20-0-600 Pa) Using Blue Gauge Fluid

Mark II Model 41-60MM Dwyer Manometer 0-60 MM

Minimum Order Quantity	1 Number
Material	Molded Plastic
Accuracy	+-3% FS
Usage/Application	Paint Booths
Brand	Dwyer
Model Name/Number	MARK II MODEL 41-60MM
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Scale Length	Approx. 8-1/4″ (21 cm).

Mark II Model 41-60MM Dwyer Manometer 0-60 MM Dwyer MARK II 41-60MM Molded Plastic Inclined Manometer, 0-60 mm w.c., Blue Gauge Fluid

Product Features:

Range: 0-60 mm w.c.
Blue Gauge Fluid
Accuracy: ±3% FS
Pressure Limits:15 psi (100 kPa)
Rapid Shutoff Pressure Connections and integral overpressure safety Traps

Applications:

Air Velocity
Air Filter Gauge

The Dwyer MARKII4160MM Molded Plastic Inclined Manometer, 0-60 mm w.c., Blue Gauge Fluid provides linear calibration and excellent resolution throughout its range. This model is capable of pressure measurements above and below atmospheric as well as differential pressure measurements. The MARK II 41-60MM includes accessories to enable portable use of the unit.

2 – Tubing connectors for 1/8 in. pipe or sheet metal ducts
2 – Mounting screws
2 – 4-1/2” lengths of clear plastic tubing
1 – Plastic swing-out stand
1 – Leveling screw
1 – 1 ounce bottle of indicating fluid
1 – Set of red and green pointer flags
1 – User Manual

Model -A-489 Dwyer A-489 SS Straight Static Pressure Tip with Flange, 4″ (101 mm) Insertion Depth

Mark II M – 700Pa Dwyer Manometer 10-0-700 Pa

Minimum Order Quantity	1 Number
Measuring Range	10-0-700 PA
Accuracy	3%
Material	Molded Plastic
Usage/Application	Paint Booths
Model Name/Number	MARK II M – 700PA
Brand	Dwyer
Weight	250 g

Mark II M – 700Pa Dwyer Manometer 10-0-700 Pa

Dwyer MARK II M-700PA Inclined/Vertical Manometer (10-0-700Pa) Using Red Gauge Oil
Model: MARK II M-700PA

Construction – Mark II Manometers are Economically Priced, Compact and Available in Both Stationary and Portable Configurations. Construction is Simple with Virtually indestructible Molded white Styrene-Acrylonitrile Housing, indicating tube and fluid wells, Molded ABS Knobs and Zero adjust plunger, shock Mounted Glass level vial and Leak Proof “O” Ring Seals.

Description:

Dwyer MARK II M-700PA Molded Plastic Manometer, Range 10-0-700 Pa
The Dwyer Mark II M-700PA Molded Plastic Manometer has a Range of 10-0-700 Pa, Red Oil, .829 sp. gr.

Dwyer® Mark II Series Molded Manometers are of the inclined and inclined-Vertical Types. The curved inclined-vertical Tube of the Model 25 gage provides higher Ranges with more easily read increments at low readings. The Model 25 is excellent for general purpose work. The Model 40 inclined gage provides linear calibration and excellent resolution throughout its range. The Model 40 is ideally suited for Air Velocity and Air Filter gage Applications. Both Gage Types are Capable of Pressure Measurements above and below Atmospheric as well as Differential Pressure Measurements.

Included:

What”s included With the Dwyer MARK II M-700PA
Dwyer MARK II M-700PA Inclined/Vertical Manometer (10-0-700Pa) Using Red Gauge Oil

Mark II MM-180 Dwyer Manometer 0-180 MM W.C

Minimum Order Quantity	1 Number
Accuracy	+-3% FS
Brand	Dwyer
Model Name/Number	MARK II MM-180
Weight	1.04 lb (472 g)/1.23 lb (558 g)
Temperature Limits	140 deg F (60 deg C)/150 deg F (65 deg C)
Pressure Limits	10 psi (70 kPa)/15 psi (100 kPa)
Scale Length	Approx. 8-1/4″ (21 cm)

Mark II MM-180 Dwyer Manometer 0-180 MM W.C

Dwyer Mark II MM-180 Inclined/Vertical Manometer (0-180mm w.c.) Using Blue Gauge Oil
Model: MARK II MM-180

Construction – Mark II Manometers are Economically Priced, Compact and Available in Both Stationary and Portable Configurations. Construction is Simple with Virtually indestructible Molded white Styrene-Acrylonitrile Housing, indicating tube and fluid wells, Molded ABS Knobs and Zero adjust plunger, shock Mounted Glass level vial and Leak Proof “O” Ring Seals.

Description:

Dwyer MARK II MM-180 Molded Plastic Manometer 0-180 mm w.c.
The Dwyer Mark II MM-180 Molded Plastic Manometer Has a Range of 0-180 mm w.c., Blue Oil, 1.91 sp. gr.

Dwyer® Mark II Series Molded Manometers are of the inclined and Inclined-Vertical Types. The curved inclined-vertical tube of the Model 25 gage provides higher ranges with more easily read increments at low readings. The Model 25 is excellent for general purpose work. The Model 40 inclined gage provides linear calibration and excellent resolution throughout its range. The Model 40 is ideally suited for Air Velocity and Air Filter Gage Applications. Both gage types are capable of pressure measurements above and below atmospheric as well as Differential Pressure Measurements.

Included:

What”s Included With The Dwyer MARK II MM-180
Dwyer Mark II MM-180 Inclined/Vertical Manometer (0-180mm w.c.) Using Blue Gauge Oil

Mark II MM-80 Dwyer Manometer 0-80 MM W.C

Minimum Order Quantity	1 Piece
Material	Molded Plastic
Accuracy	3%
Usage/Application	Paint Booths
Pressure Range	0-80 MM W.C
Brand	Dwyer
Model Name/Number	MARK II MM-80
Weight	250 f

Mark II MM-80 Dwyer Manometer 0-80 MM W.C

Dwyer Mark II MM-80 Inclined/Vertical Manometer (0-80mm w.c.) using Red Gauge OilModel: MARK II MM-80

Dwyer Mark II MM-80 Inclined/Vertical Manometer (0-80mm w.c.) Using Red Gauge Oil
Model: MARK II MM-80

Construction – Mark II Manometers are Economically Priced, Compact and Available in Both Stationary and Portable Configurations. Construction is Simple With Virtually Indestructible Molded White Styrene-Acrylonitrile Housing, Indicating Tube and Fluid Wells, Molded ABS Knobs and Zero Adjust Plunger, Shock Mounted Glass level vial and Leak Proof “O” Ring Seals.

Description:

Dwyer MARK II MM-80 Molded Plastic Manometer, 0-80 mm w.c.
The Dwyer Mark II MM-80 Molded Plastic Manomater has a range of 0-80 mm w.c., red oit, .829 sp. gr.

Dwyer® Mark II Series Molded Manometers are of The Inclined and Inclined-Vertical Types. The curved inclined-vertical tube of the Model 25 Gage Provides Higher Ranges with More Easily Read increments at low readings. The Model 25 is excellent for General Purpose work. The Model 40 inclined Gage provides linear calibration and excellent resolution throughout its range. The Model 40 is ideally suited for Air Velocity and Air Filter Gage Applications. Both gage Types Are Capable of Pressure Measurements above and below atmospheric as well as Differential Pressure Measurements.

What”s included with the Dwyer MARK II MM-80

Dwyer Mark II MM-80 Inclined/Vertical Manometer (0-80mm w.c.) Using Red Gauge Oil

Dwyer Fittings Accessories, Dwyer USA Mark II Plastic Manometer Wholesaler, Magnehelic Gages Nozzle Wholesaler in Delhi, Magnehelic Gauge Nozzle Manufacturer, Magnehelic Gauge SS Box at Best Price in Delhi, Magnehelic Gauge SS Box at Best Price in INDIA

Dumbo Pressure Plastic Manometer/Test Probe

https://www.envirotechindustrialproducts.

Dumbo Pressure Plastic Manometer/Test Probe

Product Name: Dumbo Pressure Plastic Manometer / Test Probe
Material: High Quality Plastic / Nylon
Color: Black
Application: Differential Pressure Gauge, Manometer, Magnehelic Gauge, HVAC Systems, AHU, Clean Room, Filter Monitoring
Connection Type: Hose Connection for Flexible Tubing
Installation: Wall, Duct, AHU Panel, or Filter Housing Mounting

Features:

Lightweight and durable construction
Corrosion resistant plastic body
Easy installation with mounting flange
Suitable for positive, negative, and differential pressure measurement
Compatible with most manometers and differential pressure gauges
Ideal for airflow and filter pressure drop monitoring

Common Uses:

AHU (Air Handling Unit)
HVAC Systems
Clean Rooms
HEPA Filter Monitoring
Pharmaceutical Industries
Hospitals
Food Processing Plants
Industrial Ventilation Systems

Available From:

ENVIRO TECH INDUSTRIAL PRODUCTS (Since 1995)
Delhi NCR, India

This Component Is Commonly Known In The HVAC Industry as a Dumbo Pressure Port, Pressure Test Probe, Static Pressure Probe, or Manometer Test Probe.

Additional Information:

Item Code: Dumbo Pressure Plastic Manometer/Test Probe
WhatsApp No.9871034100,9868958924,9650264867,9716640145,8368866030,8368801023
www.envirotechindustrialproducts.co.in
www.envirotechindustrialproduct.co.in
www.envirotechindustrialproduct.in
www.envirotechindustrialproducts.in
www.envirotechindustrialproduct.com
www.envirotechindustrialproducts.com
www.envirotechindustrialproducts.net
www.envirotechindustrialproduct.net

Dwyer USA Mark II Plastic Manometer Wholesaler, Magnehelic Gages Nozzle Wholesaler in Delhi, Magnehelic Gauge Nozzle Manufacturer, Magnehelic Gauge SS Box at Best Price in Delhi, Magnehelic Gauge SS Box at Best Price in INDIA, PRESSURE

DUMBO.0000 PRESSURE TEST OUTLET WITH 90° CONNECTION

DUMBO.0000 PRESSURE TEST OUTLET WITH 90° CONNECTION

Product Description:

DUMBO.0000 Pressure Test Outlet with 90° Connection is a High-Quality Pressure Measuring Port Designed For Quick And Accurate Pressure Testing in HVAC, Clean Room, Air Handling Units (AHU), Ducts, Filters, And Ventilation Systems. The 90-Degree Connection Design Provides Easy Tubing Access In Compact Installation Spaces And Ensures Reliable Pressure Monitoring.

Features:

Made From Durable Engineering Plastic Material.
90° Angled Connection For Convenient Hose Attachment.
Suitable for positive, negative, and differential pressure measurement.
Easy Installation On Ducts, Panels, And Filter Housings.
Leak-Proof Design For Accurate Readings.
Compatible With Magnehelic Gauges, Differential Pressure Gauges, and Manometers.
Corrosion-Resistant And Lightweight Construction.
Available in Black Color.

Applications:

HVAC Systems
AHU and FCU Units
Clean Rooms
HEPA Filter Monitoring
Dust Collector Systems
Pharmaceutical Industry
Food Processing Industry
Industrial Ventilation Systems

Specifications:

Model: DUMBO.0000
Connection Type: 90° Pressure Test Outlet
Material: Engineering Plastic
Color: Black
Application: Air and Gas Pressure Measurement
Installation: Panel or Duct Mounting

EX STOCK AVAILABLE – MADE IN INDIA 🇮🇳

ENVIRO TECH INDUSTRIAL PRODUCTS (Since 1995)
Delhi NCR, India
Manufacturer, Supplier & Stockist of HVAC and Differential Pressure Accessories.

Additional Information:

Item Code: DUMBO.0000 PRESSURE TEST OUTLET WITH 90° CONNECTION
WhatsApp No.9871034100,9868958924,9650264867,9716640145,8368866030,8368801023
www.envirotechindustrialproduct.net
www.envirotechindustrialproductsindia.in
www.envirotechindustrialproductsdelhi.com
www.envirotechindustrialproduct.info
www.envirotechindustrialproducts.info
www.envirotechdelhi.com

www.envirotechindustrialproductsdelhi.com

Dwyer Flowmeter Wholesaler In India, Dwyer USA Mark II Plastic Manometer Wholesaler, Magnehelic Gages Nozzle Wholesaler in Delhi, Magnehelic Gages Wholesaler in Delhi., Magnehelic Gauge Nozzle Manufacturer, Magnehelic Gauge SS Box at Best Price in Delhi, Magnehelic Gauge SS Box at Best Price in INDIA, Mounting Options Dwyer Instruments, PRESSURE

Dumbo Pressure Test Outlet With 90° Connection / ENVIRO TECH AHU

Nov 15, 2020 by admin 0 Comments 90 Degree Pressure Connection, 90 Degree Pressure Port, AHU Accessories India, AHU Differential Pressure Port, AHU Pressure Port, AHU Pressure Sampling Port, AHU Pressure Test Outlet, AHU Spare Parts India, AHU Test Port, Air Duct Pressure Port, Air Filter Pressure Port, Air Flow Test Port, Air Handling Unit Accessories., Air Handling Unit Test Port, Air Washer Pressure Outlet, Business, Clean Room Pressure Port, Differential Pressure Gauge Port, Differential Pressure Measurement Port, Differential Pressure Test Port, Duct Pressure Test Point, Dumbo Pressure Outlet India, DUMBO Pressure Test Outlet, Dumbo Test Outlet, ENVIRO TECH AHU Accessories, ENVIRO TECH HVAC Products, ENVIRO TECH Pressure Port, Filter Monitoring Port, HVAC Accessories India, HVAC Monitoring Port, HVAC Pressure Accessories, HVAC Pressure Outlet, HVAC Spare Parts, HVAC Test Connection, Industrial HVAC Components, Industrial Pressure Port, Magnehelic Gauge Port, Management, Plastic Pressure Test Outlet, Pressure Gauge Connection Port, Pressure Measurement Port, Pressure Measuring Point, Pressure Port Delhi, Pressure Port Manufacturer, Pressure Port Manufacturer India, Pressure Port Supplier, Pressure Sensor Connection, Pressure Test Nipple, Pressure Test Outlet 90 Degree, SS Pressure Test Outlet, Static Pressure Outlet, Static Pressure Test Point, Test Probe Connection

Dumbo Pressure Test Outlet With 90° Connection / ENVIRO TECH AHU

Product Name: Dumbo Pressure Test Outlet With 90° Connection
Brand: ENVIRO TECH
Material: High Quality Nylon / Fiberglass Reinforced Plastic
Color: Black
Connection Type: 90° Elbow Connection
Application: AHU, HVAC Systems, Clean Room, Air Washer Unit, Differential Pressure Measurement
Suitable For: Magnehelic Gauge, Differential Pressure Gauge, Manometer, Pressure Transmitter
Installation: Mounted through AHU Panel or Door For Easy Pressure Testing.

Features:

- Compact and Durable Design.
- 90° Outlet Keeps The Tubing Close To The Panel.
- Prevents Accidental Disconnection Of Rubber Tubes.
- Corrosion Resistant And Light Weight.
- Easy Installation And Maintenance.

Country of Origin: Made in India 🇮🇳
Availability: Ex Stock Available.

Product Description:

The Dumbo Pressure Test Outlet With 90° Connection is Designed For Connecting Air Pressure Measuring Instruments Inside AHU and HVAC systems. It Provides a Convenient Connection Point For Rubber Tubing Used With Magnehelic Gauges, Differential Pressure Gauges, and Manometers. The 90-Degree Design Allows The Tube to Remain Close To The Panel Surface, Reducing Obstruction And Minimizing The Risk Of Accidental Disconnection During Operation. It is Manufactured From Durable Fiberglass Reinforced Nylon For Long Service Life And Reliable Performance In Industrial Applications.

Additional Information:

Item Code: Dumbo Pressure Test Outlet With 90° Connection / ENVIRO TECH AHU
WhatsApp No.9871034100,9868958924,9650264867,9716640145,8368866030,8368801023
www.envirotechindustrialproduct.net
www.envirotechindustrialproductsindia.in
www.envirotechindustrialproductsdelhi.com
www.envirotechindustrialproduct.info
www.envirotechindustrialproducts.info
www.envirotechdelhi.com

Dwyer Fittings Accessories, Dwyer Fittings Accessories, Magnehelic Gages Nozzle Wholesaler in Delhi, Dwyer USA Mark II Plastic Manometer Wholesaler, Magnehelic Gages Nozzle Wholesaler in Delhi, Magnehelic Gauge Nozzle Manufacturer, Magnehelic Gauge SS Box at Best Price in Delhi, Magnehelic Gauge SS Box at Best Price in INDIA, Mounting Options Dwyer Instruments, Static Pressure Tips & Accessories Dwyer Instruments

PVC COMPONENTS AIR PRESSURE CHECK NOZZLE

PVC COMPONENTS AIR PRESSURE CHECK NOZZLE

PVC Components Air Pressure Check Nozzle is a High-Quality Air Pressure Sensing Nozzle Designed for Accurate Measurement of Differential Pressure, Static Pressure, And Airflow in HVAC, Clean Room, And Industrial Ventilation Systems. Manufactured From Durable PVC Material, it Offers Excellent Resistance To Corrosion, Moisture, And Chemicals, Ensuring Long Service Life And Reliable Performance.
Features:

Made From High-Quality PVC material.
Corrosion And Chemical Resistant Construction.
Lightweight And Easy To Install.
Suitable For Positive, Negative, And Differential Pressure Measurement.
Flange Mounting Design For Secure Installation.
Provides Accurate Air Pressure Sensing.
Low Maintenance And Long Operational Life.

Applications:

HVAC Systems
AHU (Air Handling Units)
Clean Rooms
Dust Collection Systems
Air Filters Monitoring
Ventilation and Exhaust Systems
Pharmaceutical Industries
Food Processing Industries
Industrial Airflow Monitoring

Specifications:

Material: PVC
Connection Type: Air Pressure Check Nozzle
Mounting: Flange Type with Two Fixing Holes
Application: Air Pressure and Differential Pressure Measurement
Color: Black
Country of Origin: Made in India

ENVIRO TECH INDUSTRIAL PRODUCTS (Since 1995) Supplies High-Quality PVC Air Pressure Check Nozzles For Industrial And HVAC Applications With Reliable Performance And Competitive Pricing.

Additional Information:

Item Code: PVC COMPONENTS AIR PRESSURE CHECK NOZZLE
WhatsApp No.9871034100,9868958924,9650264867,9716640145,8368866030,8368801023
www.envirotechindustrialproducts.net
www.envirotechindustrialproduct.net
www.envirotechindustrialproductsindia.in
www.envirotechindustrialproductsdelhi.com
www.envirotechindustrialproduct.info
www.envirotechindustrialproducts.info
www.envirotechdelhi.com

MAGNEHELIC GAGES SS 304 NOZZLE

MAGNEHELIC GAGES SS 304 NOZZLE

Magnehelic Gages SS 304 Nozzle is a High-Quality Stainless Steel Pressure Sensing Nozzle Specially Designed for use with Magnehelic Differential Pressure Gauges, Differential Pressure Transmitters, and Manometers. The Nozzle is Manufactured From Premium Quality SS 304 Stainless Steel, Providing Excellent Corrosion Resistance, Durability, and long service life in industrial environments. It is widely used for measuring Differential Pressure, Static Pressure, Air Velocity, And Filter Pressure Drop in HVAC And Clean Room Applications.

Product Features:

Manufactured From Premium Grade SS 304 Stainless Steel
Corrosion Resistant And Rust-Proof Construction
Compact And Robust Design
Easy Installation On Ducts And AHU Panels
Accurate Pressure Sensing Performance
Suitable For Positive, Negative And Differential Pressure Measurement
Long Service Life With Minimal Maintenance
Compatible With Magnehelic Gauges and Differential Pressure Instruments.

Technical Specifications:

Material: SS 304 Stainless Steel
Connection Type: Hose Barb / Tube Connection
Thread Connection: Suitable For Standard Panel Mounting
Finish: Polished Stainless Steel
Media: Air and Non-Corrosive Gases
Application: Pressure Sensing And Air Velocity Monitoring
Country of Origin: Made in India.

Applications:

HVAC Systems
AHU and FCU Units
Clean Rooms
Pharmaceutical Industries
Hospitals and Operation Theatres
HEPA Filter Monitoring
Duct Static Pressure Measurement
Fan and Blower Pressure Monitoring
Differential Pressure Measurement Systems.

Product Identification From Your Image:

The Item Shown In Your Photo Appears To Be An SS 304 Pressure Pickup Nozzle / Magnehelic Gauge Nozzle With Hose Connection For Pneumatic Tubing. It is Commonly Installed On AHU Ducts, Filter Housings, And Clean Room Panels To Connect Tubing Between The Pressure Source And a Magnehelic Differential Pressure Gauge.

Additional Information:

Item Code: MAGNEHELIC GAGES SS 304 NOZZLE
WhatsApp No.9871034100,9868958924,9650264867,9716640145,8368866030,8368801023
www.envirotechindustrialproducts.co.in
www.envirotechindustrialproduct.co.in
www.envirotechindustrialproduct.in
www.envirotechindustrialproducts.in
www.envirotechindustrialproduct.com
www.envirotechindustrialproducts.com

+(91)-9871034100

07AOSPS8386M1ZM

DWYER OMEGA / MAGNEHELIC DIFFERENTIAL PRESSURE GAUGE NEAR Huda Industrial Area Ballabgarh Haryana

Magnehelic / Differential Pressure Gauge In Kotda Sangani Industrial Area Rajkot Gujarat

Dwyer USA Mark II Plastic Manometer Wholesaler

Mark II Model 40-1-AV Dwyer Manometer Range 0-1.1 Inches w.c

Mark II Model 40-1 Dwyer Manometer Range .1-0-1.0 Inches W.C

Mark II Model 28 Dwyer Manometer Range 0-10,500 FPM

Mark II Model 27 Dwyer Manometer Range 0-7000 FPM

Mark II Model 26 Dwyer Manometer Range 0-7 Inches WC