Elementor #2070 – envirotechdelhi.co.in

Battery Powered Temperature Indicator

Rs 2,500 / Piece

Usage/Application	Provides local temperature indication in areas without power availability
Weight	6.0 oz (170 g).
Brand	DWYER USA
Condition	New
Model	Series-BPI
Power Requirements	3.6 V AA lithium metal battery, included, user replaceable.
Battery Life	2 years.
Display	0.3″ (7.6 mm) 4-digit LCD.
Resolution	0.1 Degree C.
Ambient Operating Temperature	14 to 158 Degree F (-10 to 70 Degree C).
Storage Temperature	4 to 185 Degree F (-20 to 85 Degree C).
Front Panel Protection	NEMA 4X (IP66).

Battery Powered Temperature Indicator

The Series BPI Battery Powered Indicator accepts RTD or Thermocouple input and provides local or remote display of temperature measurements. Quickly navigate the menu system to customize for each application. Three push buttons allow the user to select input type, engineering units (°F or °C), offset temperature, decimal point position, and password protection. The indicator is housed in a polycarbonate NEMA 4X (IP66) enclosure for additional protection from the environment.

Features:

Programmable input type, engineering units (°F/°C), offset temperature, decimal point position, and password protection
Four-digit segmented display

Applications:

Provides local temperature indication in areas without power availability

Installation:
Configuration:
Fit the battery as described in Battery section, then follow the simple configuration menus printed on the reverse side of this sheet. This procedure can be performed with or without the sensor connected. Fit the correct units legend to the front panel face.

Enclosure:
The case offers various options for sensor entry. Please refer to the data sheet for further details. The sensor may be fixed directly to the housing, or remotely connected using cable and gland. Cable length must be no greater than 20 meters to comply with CE certification. All external cabling/sensor entries must maintain IP67 rating.

Additional Information:

Item Code: Series-BPI

Digital Indicating Transmitter

Rs 8,700 / Piece

Power Requirement	20 to 35 VDC.
Operating Temp	-6 to 140 Degree F (-20 to 60 Degree C)
Application	Electrically isolates pressure and level transmitters from unregulated circuits for intrinsically sa
Applications	Electrically isolates pressure and level transmitters from unregulated circuits for intrinsically sa
Condition	New
Brand	DWYER USA
Humidity	5 to 95% RH.
Storage Temperature	-40 to 176 Degree F (-40 to 80 Degree C).
Model Number	Series-MTL5541
Automation Grade	Manual
Weight	150 g.
LED Indicator	Green Power Indication.

Digital Indicating Transmitter

The SERIES MTL5541 Galvanic Barrier provides intrinsically safe isolation for communication with Dwyer® transmitters approved for use in hazardous areas. This galvanic barrier eliminates the need for a high integrity earth ground required when using shunt type diode type safety barriers. DIN rail mounting and plug-in signal and power connectors simplify installation and maintenance.

Features:

Designed to mount on most standard DIN rails
Approved for use in hazardous areas

Specification:

Hazardous Area Input : Signal range: 0 to 24 mA (including over-range); Transmitter voltage: 16.5 V at 20 mA.
Safe Area Output : Signal range: 4 to 20 mA; Under/over-range: 0 to 24 mA;Load resistance: 0 to 360Ω @ 24 mA, or 0 to 450Ω @ 20 mA; Current sink: 600Ω max.; Maximum Voltage Source: 24 VDC; Output resistance: > 1 MΩ.
Response Time : Settles to within 10% of final value within 50 µs.
Current Consumption (20 mA signal) : 51 mA @ 24V.
Maximum Power Dissipation (20 mA signal) : 0.7 W @ 24 VDC, 1.0 W @ 24 VDC.
Isolation : 250 V RMS, tested at 1500 V RMS minimum, between safe- and hazardous-area terminals; 50 V between safe-area circuits and power supply.
Transfer Accuracy at 68°F (20°C) : Better than 15 µA.
Temperature Drift : < 0.8µA/°C.
Mounting : T-section 35mm DIN rail (7.5 or 15mm) to EN 50022.
Terminals : Accommodate up to 2.5 mm2 stranded or single-core.
Safety Description : Vo= 28 V, Io= 93 mA, Po= 651mW, Um= 253 RMS or DC.

Applications:

Electrically isolates pressure and level transmitters from unregulated circuits for intrinsically safe applications

Additional Information:

Item Code: Series-MTL5541

Indicating Alarm Annunciator

Rs 2,650 / Piece

Usage/Application	Tank level monitoring
Model No.	Series-AN2
Brand	DWYER USA
Weight	9.6 oz (272 g).
Application	Water and wastewater panels
Ambient Operating Temperature	-40 to 149 Degree F (-40 to 65 Degree C).
Mounting	1/8 DIN.
Housing Material	UL rated 94V-0 high impact plastic.
Enclosure Rating	NEMA 4X (IP65) front panel.
Power Consumption	20 W (6 W on low voltage models).

Indicating Alarm Annunciator

The Series AN2 Indicating Alarm Annunciator provides visible and audible alarms for up to eight inputs. The annunciator also has two SPDT relay outputs that can be used to initiate external alarms, buzzers, or paging devices. The Integral 24 VDC power supply can power most level, temperature, pressure, and flow switches. Audible alarm conditions can be acknowledged, reset, or silenced either via the front panel push buttons or the rear terminal block. The Series AN2 can be set to any common ISA sequences including First-Out.

Features:

Includes integral 24 VDC power supply to power most switches
Can be set to any common ISA sequences

Specification:

Inputs : NO or NC switches, Open Collector Transistor (Open circuit voltage = 3.3 VDC); Logic Levels: LO = 0 to 0.9 VDC, HI = 2.4 to 28 VDC (100 KΩ input impedance).
Outputs : Two SPDT relay (3 A @ 250 VAC or 30 VDC, resistive; 1/14 HP @ 125/250 VAC, inductive).
Power Requirements : 85 to 265 VAC 50/60 Hz, 90 to 265 VDC; 12 to 36 VDC, 12 to 24 VAC (depending on model).

Applications:

Water and wastewater panels
Tank level monitoring
Temperature monitoring process

Other Details:

Model	Number of Outputs	Power Supply
AN24-1	4	85 to 265 VAC
AN24-2	4	12 to 36 VDC
AN28-1	8	85 to 265 VAC
AN28-2	8	12 to 36 VDC

Additional Information:

Item Code: Series-AN2

Miniature Current Switch

Rs 6,400 / Piece

Weight	0.5 oz (14.5 g).
Application	BAS
Model No.	Series-MCS
Brand	DWYER USA
Amperage Range	MCS-111050 0.5 to 50 A AC continuous; MCS-111001 0.01 to 1 A AC continuous.
Output Rating	Isolated, N.O. 0.3 A 130 V DC/AC.
Hysteresis	1%.
Response Time	200 ms.
Temperature Limits	32 to 122 Degree F (0 to 50 Degree C).
Humidity	10 to 95% RH (non-condensing).
Enclosure Rating	UL 94V-0 flammability rated ABS, insulation class 600 V.

Miniature Current Switch

The SERIES MCS Miniature Current Switches are ideal for monitoring the current usage in fuse boxes and small control panels. Both models have adjustable set points and LED indication to show there is power to the unit and when the switch activates. Set points can be adjusted using the potentiometer next to the LED’s. Due to the size of the switch, it is only offered in solid core and no core versions. The no core version has terminal blocks which can accept currents up to 1 A directly into the unit.

Features:

Integral mounting flange for quick installation
Compact size fits in any space

Applications:

BAS
HVAC.

Other Details:

Model	Case	Set Point	Minimum Set Point (A)	LED
MCS-111050	Solid core	Adjustable	0.5	Red/geen
MCS-111001	No core (terminal connection)	Adjustable	0.01	Red/geen

Additional Information:

Item Code: Series-MCS

Series SCS Current Switch

Rs 3,250 / Piece

Brand	Dwyer Usa
Temperature Range	5 to 140 Degree F (-15 to 60 Degree C).
Condition	New
Model	Series-SCS
Application	BAS
Frequency	50/60 Hz.
Place Of Origin	DELHI
Output	Isolated, 1 A 30 VAC/DC max, NO.
External Relay	SPST N.O., 10A at 260 VAC (5A at 30 VDC).
Power	None, self-powered.
Isolation Voltage	600 VAC RMS.
Enclosure Rating	UL, 94 V-O flammability rated, ABS plastic housing.

Series SCS Current Switch

The Series SCS Low Cost Current Switches are ideal for monitoring whether fans, pumps, or motors are operating. The current flowing through the core of the device powers the circuit without an external power supply. All models have a built in solid state output and are easy to install. Optional LED’s and 10 Amp relay modules are available. The Series SCS is available in both Split and Solid Core configurations.

Features:

Integral mounting flange for quick installation
Solid core or split core configurations

Applications:

BAS
HVAC

Other Details:

Model	Case	Amperage Range	Set Point	Switch Mode	Snap-on Relay
SCS-120025	Solid	.25 to 200 A	0.25 fixed	Under	No
SCS-111100	Solid	1 to 135 A	Adjustable	Over/under	No
SCS-111100-R	Solid	1 to 135 A	Adjustable	Over/under	Yes
SCS-220015	Split	.15 to 200 A	0.15 fixed	Under	No
SCS-220150	Split	1.5 to 200 A	1.5 fixed	Under	No
SCS-211125	Split	1.25 to 135 A	Adjustable	Over/under	No
SCS-220150-R	Split	1.5 to 200 A	1.5 fixed	Under	Yes
SCS-211125-R	Split	1.25 to 135 A	Adjustable	Over/under	Yes

Additional Information:

Item Code: Series-SCS

Vibration Transmitter

Rs 24,500 / Piece

Brand	DWYER USA
Temperature Range	-22 to 221 Degree F (-30 to 105 Degree C).
Application	Industrial
Weight	0.28 lb (0.125 kg)
Model No	Model-VBT-1
Condition	New
Usage/Application	Motors
Enclosure Rating	NEMA 6 (IP68).
Housing Material	316 SS.
Electrical Rating	9.6 to 32 VDC.
Frequency Range	10 to 1000 Hz.
Output Signal	4 to 20 mA.

Vibration Transmitter

The Model VBT-1 Vibration Transmitter continuously detects the vibration in a system and monitors for unusual operating conditions and potential failure. The vibration is converted into an analog signal at the current output. The VBT requires no setup, and there is no software required for configuration. The 2-wire loop power operation, combined with standard M12 micro cable connector and interchangeable mounting studs (1/4″-28 UNF/M8 (2) or the 1/4″-28 UNF), makes for a fast and reliable installation.

Features:

Easy set-up and operating concept
Stainless steel housing
No software required

Specification:

Accuracy : < ±3%.
Connections : M12 connector.
Mounting Orientation : Any position.
Nonlinearity : < ±0.25% of span.
Repeatability : < 0.5%.

Applications:

Motors
Pumps
Fans
Engines
Compressors
Gear boxes

Additional Information:

Item Code: Model-VBT-1

Series CCS Current Switch

Rs 1,850 / Piece

Model Number	Series-CCS
Temperature	-22 to 158 Degree F (-30 to 7 Degree C).
Humidity	0 to 95% (non-condensing).
Application/Usage	BAS
Condition	New
Brand	DWYER USA
Connection	New
Frequency	40 to 400 Hz.
Usage/Application	HVAC
Amperage Range	0 to 200 A AC.
Output	Normally open, NPN.
Isolation Voltage	2000 V.
Enclosure Rating	UL, 94 V-O flammability rated, ABS plastic housing.

Series CCS Current Switch

The SERIES CCS Current Switches are ideal for monitoring the operating status of fans, pumps, and motors. These self-powered switches can be hung or tied directly to cables or wires. For use on existing installations, split core models can be installed without disconnecting cables. LED indicators provide a visual confirmation that the current is flowing through the core. Both fixed and adjustable set points are available. The adjustable models utilize a potentiometer to easily adjust the set point.

Features:

Integral mounting flange for quick installation
Solid core or split core configurations
LED Indicator
Maximum Switch Rating : For fixed set point models: 0.3 A @ 135 VAC/DC; For adjustable set point models: 1 A @ 240 VAC.

Applications:

BAS
HVAC

Other Details:

Model	Case	Set Point	Minimum Set Point (A)	LED	Dry Contact Output
CCS-121050	Solid core	Fixed	0.50 (±0.2)	Red	Yes
CCS-111100	Solid core	Adjustable	1.00 (±0.2)	Red/green	No
CCS-221100	Split core	Fixed	1.00 (±0.2)	Red	Yes
CCS-211150	Split core	Adjustable	1.50 (±0.2)	Red/green	No
CCS-131100	Solid core	Adjustable	1.00 (±0.2)	Red/green	Yes
CCS-231150	Split core	Adjustable	1.50 (±0.2)	Red/green	Yes

Additional Information:

Item Code: Series-CCS

Bar Graph Meter

Rs 8,500 / Piece

Model	Series-BGM
Accuracy	+/-0.05% FS.
Condition	new
Storage Temperature	-67 to 176 Degree F (-55 to 80 Degree C).
Usage	Laboratory
Weight	40 oz (1.13 kg)
Operating Temperature	13 to 176 Degree F (-25 to 80 Degree C)
Brand	DWYER USA
Enclosure Rating	NEMA 1 or NEMA 4Xt model dependent IP65 front.
Decimal Point	3 positions, user selectable.
Outputs	2 SPST relay outputs (optional).
Time Delay	0.5 S
Input Range	0 to +/-10 VDC or 4 to 20 mA.

Bar Graph Meter

The Series BGM Digital Bar Graph Meter is extremely durable and can replace a wide range of analog meters. The 4-digit display will significantly reduce the potential for human error in reading by eliminating errors commonly produced by the viewing angle when reading analog meters. This series has a key pad that allows for easy access of features without complex menu structures. With the combined ability to create a wide range of custom faceplate and the optional NEMA 4X bezel, the Series BGM can be used in a variety of applications. The LED bar graph adds a visual indicator of the measured value so that it can be visually analyzed, preventing accidents or system failures from happening.

Features:

Bar graph visual indicator
High resolution for better precision
Many configurable options to design a meter for any need

Specification:

Power Requirements : 120 VAC 50/60 Hz, 5 to 12 VDC, or 10 to 30 VDC model dependent.
Power Consumption : 120 VAC: 2.4 W @ 20 mA max; 5 to 12 VDC: 1.2 W @ 100 mA max; 10 to 30 VDC: 1.5 W @ 50 mA max.
Display : LED Display: 4 red colored digits, 0.3″ height; LED Graph: 31 element bar, 0.2″ W x 3.1″ L (5.08 mm W x 78.74 mm L).
Electrical Connections : Removable screw terminal blocks.
Switch Rating : 1 A @ 200 V.
Enclosure Material : Bezel: Black epoxy enameled steel; Window: Acrylic; Case and Mounting Bracket: 304 SS.

Applications:

Visual location and indication of flow, level or air velocity

Additional Information:

Item Code: Series-BGM

Digital Timer / Tachometer / Counter

Rs 750 / Piece

Operating Temp.	32 to 122 Degree F (0 to 50 Degree C).
Humidity	35 to 85% RH (non-condensing).
Application	Industrial
Weight	4 oz (114 g).
Model Number	Series-LCT216
Display Type	Digital
Brand	DWYER USA
Condition	New
Reset Time	0.001 S. minimum.
Power Requirements	100 to 240 VAC 50 / 60 Hz.
Power Consumption	Less than 10 VA.
Internal Power Supply	12 VDC +/-10%, 100 mA.

Digital Timer / Tachometer / Counter

The Series LCT216 combines a versatile timer, counter, and tachometer in one device. The bright, easy-to-read display shows both the desired set point and the current process value as well as the operating mode that the control is functioning in. The fourteen pre-programmed timer functions are easy to set up and cover most applications. The counting functions include one stage or two stage counting along with batch, total, or dual counting modes. The Series LCT216 can also be used as a tachometer to measure rotational speeds. For quick set up, many of the programming parameters can be set with external dip switches located on the side of the unit.

Features:

Fourteen pre-programmed timer functions
One stage, two stage, batch, total, and dual counting modes

Specification:

Control Output Ratings : (Out 1) Relay: SPST 5A at 250 VAC, Transistor: NPN Open collector 100 mA / 30 VDC residual voltage = 1.5 VDC max; (Out 2) Relay: SPST 5A at 250 VAC, Transistor: NPN Open collector 100 mA / 30 VDC residual voltage = 1.5 VDC max.
Inputs : Dry contact, PNP, or NPN.
Timing Functions : 14 pre-programmed timing functions.
Display : Two-line 6 digit negative transmissive LCD display.

Applications:

Industrial ovens
Batch counting in conveyor systems
Silk screening equipment

Additional Information:

Item Code: Series-LCT216

Electronic Fan Speed Control

Rs 4,500 / Piece

Condition	New
Weight	1 lb 11 oz (.77 kg).
Model Number	Model-FC-1000
Connection	New
Temperature Range	-40 to 131 Degree F (-40 to 55 Degree C).
Brand	DWYER USA
Line Voltage Range	120-277 VAC, 60 Hz.
Input Signal Voltage	0-10 VDC.
Low Voltage Input	24 VAC, Class 2
Input Signal Impedance	10K ohms.
Locked Rotor Amp Rating	24.0.
Enclosure Rating	NEMA 1.

Electronic Fan Speed Control

The Model FC-1000 Electronic Fan Speed Control provides precise speed modulation of small AC motors. Popular 0-10 VDC input works with most process controllers, eliminating the need for more expensive dampers, damper actuators and linkages while improving overall energy efficiency of the system. This inexpensive unit enables variable control ventilation fans, condenser fans and interfacing with VAV box controllers.

Features:

Compact design allows for use in most areas
Improves energy efficiency in systems

Specification:

Full Load Amp Rating : 9.8 @ 120 VAC, 9.3 @ 208 VAC, 8.0 @ 240 VAC, 6.9 @ 277 VAC.
Electrical Connections : Line voltage: 10-32 screw terminals; Signal and low voltage input: 1/4″ quick connects.
Transient Protection : 320V surge suppression. Exceeds IEEE C62.41 standards.
Housing Materials : Cold rolled steel.
Mounting : Vertical only; four holes provided for 10 screws.

Applications:

Monitoring fans and motors

Additional Information:

Item Code: Model-FC-1000

Ice Cube Relays

Rs 12 / Piece

Model No	Series-784-4PDT
Model Number	784-4PDT
Weight	2.8 oz (80 g).
Brand	DWYER USA
Condition	New
Application	HVAC motor controls
Operating and Load Voltage Range	24 to 120 VAC, 24 VDC
Switching Operation	4PDT
Electrical Rating	15 A 120 VAC 50/60Hz; 12 A 277 VAC 50/60 Hz or 28 VDC.
Storage Temperature	-40 to 185 Degree F (-40 to 85 Degree C)
Operation Temperature	-40 to 131 Degree F (-40 to 55 Degree C).
Power Consumption	1.5 VA; 1.5 W.
Cycle Life	200000 cycles (electrical); 10000000 cycles (mechanical).
Housing	Plastic polycarbonate.

Ice Cube Relays

The Series 784 Electromechanical Ice Cube Relay is a full-featured 4PDT relay that can be used to handle loads up to 15 amps for AC or DC circuits. Utilizing the same trigger, this relay can be used in underground parking garage applications to signal audible and visual alarms for high levels of carbon monoxide, while opening the dampers and starting the exhaust fans. It features a flag status indicator and a LED status lamp to let the user know when the relay is activated. In order to differentiate between AC and DC actuated models, the push-to-test button is color-coded. For testing the operation, a removable lockdown lever holds the test button in place. The clear plastic housing gives a view of the contacts and there is a removable I.D. tag for labeling the circuit.

Features:

Clear plastic housing to easily view the contacts
Flag and LED status indicators for visual confirmation of relay state
Socket mounted for quick installation/replacement

Applications:

Refrigeration compressor systems
HVAC motor controls
Water/wastewater pump control

Additional Information:

Item Code: Series-784-4PDT

Low Cost Digital Timer

Rs 6,700 / Piece

Model	Series-LCT316
Brand	DWYER USA
Weight	5.6 oz (158.8 g).
Usage/Application	Commercial cooking equipment
Display Type	Digital
Applications	Commercial dish washers and refrigeration equipment
Item Code	Series-LCT316
Operating Temperature	32 to 158 Degree F (0 to 70 Degree C).
Control Output Ratings	Relay, SPST, 16A at 250 VAC resistive.
Status Light	LED shows time and operation.
Inputs	Digital input for start and reset.
Supply Voltage	115 VAC, 230 VAC, 12 VAC/DC, 24 VAC/DC depending on model
Power Consumption	4VA

Low Cost Digital Timer

The Series LCT316 Low Cost Digital Timer provides accurate countdown timing for a variety of applications. The timer can be triggered remotely using the digital input terminals or locally via the set button. Time intervals can be set up to 999 minutes or seconds. The Series LCT316 has an internal buzzer to alert when the time interval has expired.

Features:

1 second to 999 minute field set time interval
Audible alarm for status indication

Applications:

Commercial cooking equipment
Commercial dish washers and refrigeration equipment

Other Details:

Model	Supply Power
LCT316-100	115 VAC
LCT316-200	230 VAC
LCT316-300	12 VAC/DC
LCT316-400	24 VAC/DC

Additional Information:

Item Code: Series-LCT316

Particulate Monitor

Rs 50,000 / Piece

Brand	DWYER USA
Condition	New
Model No	Series-DPM
Usage/Application	Baghouses
Weight	4.5 lbs (2.0 kg)
Inputs	From PMS Sensor.
Power Requirement	115 VAC 50/60 Hz, 230 VAC 50/60 Hz, or 24 VDC.
Power Consumption	6 Watts Max.
Display	LCD
Temperature	-13 to 160 Degree F (-25 to 70 Degree C).

Particulate Monitor

The DPM Particulate Monitor and PMS Particulate Sensor combine to provide a basic baghouse and cartridge filter leak detector designed for general maintenance planning and process protection. It is easy to use and reliable. Leakage is gaged in real-time, on-the-spot, without prior baseline data and without signal tuning. Simply apply power and the general condition of the filter is quickly determined. An alarm point is set by simply moving an indicator up and down the gage with the convenient, lockable key pad. For more precise alarm setup the large display provides both a logarithmic analog bar graph and an absolute digital readout. The log scale enables the user to observe both the baseline bleed through and the high peaks that are caused by filter cleaning cycles and developing leaks. Observation of both baseline and peaks is essential to setting proper alarms. The digital readout in absolute units ensures correct interpretation of the readings and provides accurate historical comparisons.

The DPM Particulate Monitor is housed in a rugged cast aluminum enclosure. An LCD displays particulate levels in bar-graph and digital forms. A lockable membrane keypad is provided for setup and adjustment.

Features:

Rugged cast aluminum housing with lockable membrane keypad
Programmable alarm points
Large LCD to display readouts digitally

Specification:

Output Ratings : Alarm Relays: 2 Form A (SPST) rated 5A @ 240V res. (must provide an 8A [maximum] fuse in series with relay load); Analog: 4 to 20 mA (Option RC).
Accuracy : Standard: ±5% of range; Optional: ±1% of range.
Display Resolution : Standard: 5 pA; Optional: 0.5 pA.
Memory Backup : For set point storage only.
Enclosure : Cast aluminum, weatherproof, NEMA 4X.
Loop Power Supply (Isolated) : 17 VDC loop supply provided by DPM control unit for PMS sensor.

Applications:

Baghouses
Cartridge Filters
Bin Vents

Request
Callback

Additional Information:

Item Code: Series-DPM

Particulate Sensor

Rs 20,700 / Piece

Model Number	Series-PMS
Ambient Temperature	-40 to 392 Degree F (-40 to 200 Degree C)
Connection	New
Condition	New
Brand	DWYER USA
Application/Usage	Cartridge Filters
Usage/Application	Baghouses
Wetted Materials	304SS and PTFE.
Electrical Connection	Low noise coaxial.

Particulate Sensor

The PMS Particulate Sensor employs a field-proven combination of passive-induction and protected-probe technologies. As particles flow near and around the probe, minute currents are dynamically induced into the probe by flowing particulate. A DSP processes the signal into an absolute output that is reasonably linear to mass. Protective layers over the probe work in combination with induction-sensing to ensure reliable operation with all types of particulate including moist powders and highly conductive dusts. Maintenance is minimal and there is no need for an air purge. For durability, the sensors are passive and free of electronics. The PMS Particulate Sensor is designed to be used with the DPM Particle Monitor in order to be intrinsically safe.

Features:

Durable housing that is free of electronics
Minimal maintenance needed

Specification:

Service : Air and compatible gases, any type particulate.
Pressure Limits : Standard: Full vacuum to 10 psi (0.69 bar); Optional: 100 psi (6.89 bar).
Output Signal : pA.
Enclosure : Standard: Painted cast aluminum, weatherproof, NEMA 4X; Optional: Intrinsically Safe, CSA.
Weight : Varies depending on length of probe and type of mount.

Applications:

Baghouses
Cartridge Filters
Bin Vents

Additional Information:

Item Code: Series-PMS

Particulate Transmitter

Rs 22,000 / Piece

Application	Filter leak or wear detection
Usage/Application	Bin vent monitoring
Accuracy	+/-5% of reading.
Model Number	Series-PMT2
Output Signal	4 to 20 mA.
Enclosure	Powder coated aluminum.
Brand	DWYER USA
Condition	New
Application/Usage	Broken bag detection in dust collectors
Applications	Emissions monitoring
Wetted Materials	316L SS, silicone, and PTFE.
Particulate Size	0.3 microns and higher.
Detection Range	5 to 5000 pA (6 selectable range options).
Pressure Limit	30 psi (2 bar).
Power Requirements	12 to 28 VDC.

Particulate Transmitter

The SERIES PMT2 Particulate Transmitter is designed to measure particulate emission levels from dust collector discharge. Using DC coupled electrostatic induction sensing technology, the transmitter monitors a pA current that is generated as particulate passes near the probe; a 4 to 20 mA signal will vary based on the particulate level. The PMT2 offers 6 sensitivity ranges allowing the user to choose the range that will best fit the application. The range and test selector switch can also be set to output a 4 mA or 20 mA signal to assist with set up or trouble shooting. Averaging time setting can be used to dampen the signal if desired.

Features:

Simple 2-wire installation for PLC and control panels
Non-stick PTFE coated probe to prevent false readings from moist and conductive dusts, condensate, and dust buildup
Remote zero calibration helps to decrease maintenance time

Specification:

Temperature Limits:Ambient: -40 to 145°F (-40 to 63°C); Process: -40 to 248°F (-40 to 120°C).
Electrical Connection : Two 1/2″ female NPT conduit openings.
Terminal Block : Removable (16 to 20 AWG wire).
Enclosure Rating : Type 4 (IP66).
Mounting Orientation : Any.
Averaging Time : 1 to 360 s (10 selectable options).
Weight: Varies with length of probe and type of mount.

Applications:

Emissions monitoring
Broken bag detection in dust collectors
Filter leak or wear detection
Bin vent monitoring

Additional Information:

Item Code: Series-PMT2

Process Indicator

Rs 5,500 / Piece

Usage/Application	Display process values from various transmitters
Condition	New
Model	Series-LCI132
Display Type	Digital
Humidity Range	95% 40 Degree C.
Brand	DWYER USA
Temperature Coefficient	100 ppm/ Degree C.
Warm Up	5 minutes
Operating Temperature	-10 to 60 Degree C
Storage Temperature	-25 to +85 Degree C
Panel Sealing	NEMA 4X (IP66).

Process Indicator

THE SERIES LCI132 PROCESS INDICATORS offer flexibility and value in a low cost, compact 1/32 DIN package. The shallow depth of these full size panel meters allows installation in panels only 2.76″ (70 mm) deep with room to spare.

Features:

Fits in 1/32 DIN panel cutouts
IP65 (NEMA 4X) front housing
Fully programmable
Various voltage and current inputs fits most processes

Specification:
Model – LCI132-0X

Range : Input Volts (DC): ±200 V, ±20 V, ±10 V; Input Amperes: ±100 mV, ±20 mA;
Resolution : Input Volts (DC): 0.1 V, 0.01 V, 1 mV; Input Amperes: 0.1 mV, 0.01 mA; Input Impedance: Volts: 1 M Ω, mV: 100 M Ω, mA: 12.1 Ω.

Model – LCI132-1X

Range AC : Input Volts: 600.0, 100.0; Input Amperes: 5.000, 1.000;
Range DC : Input Volts: -199.9, ±600.0, ±100.0; Input Amperes: -1.999, +5.000, ±1.000;
Resolution : Input Volts: 0.1 V; Input Amperes: 1 mA Input Impedance: Volts: 3 M Ω (106), Amps: 12 m Ω (10-3).
Accuracy at 23ºC ±5ºC : 100/600 VDC 1/5 A DC; 600V/5A AC: ±(0.2% reading + 3 digits). 100 V / 1A AC: ±(0.4% reading + 4 digits).

Power Supply and Fuses (DIN 41661) (Not supplied):

LCI132-X0 : 85–265 VAC 50/60 Hz and 100-300 VDC: Fuse: 0.1A/ 250V.
LCI132-X1 : 21-53 VAC 50/60Hz and 10.5-70 VDC: Fuse 0.5A/ 250V.

Display:

LCI132-X0 : 85–265 VAC 50/60 Hz and 100-300 VDC: Fuse: 0.1A/ 250V.
LCI132-X1 : 21-53 VAC 50/60Hz and 10.5-70 VDC: Fuse 0.5A/ 250V.

Applications:

Display process values from various transmitters

Other Details:

Model	Input	Supply Voltage
LCI132-00	±100 VDC; ±20 VDC; ±10 VDC; ±200 VDC; ±20 mA DC	120/240 VAC
LCI132-01	±100 VDC; ±20 VDC; ±10 VDC; ±200 VDC; ±20 mA DC	24/48 VAC
LCI132-10	±100 VAC; 600 VAC; 5 A (DC) 1A (AC); -199.9 to +600 VDC; ±100 VDC -1.999 to 5 A (DC) ±1 A (DC);	120/240 VAC
LCI132-11	±100 VAC; 600 VAC; 5 A (DC) 1 A (AC); -199.9 to +600 VDC; ±100 VDC -1.999 to 5 A (DC) ±1 A (DC);	24/48 VAC

Additional Information:

Item Code: Series-LCI132

Process and Temperature Alarm Switch Module

Rs 6,500 / Piece

Operating Temperature	32 to 131 Degree F (0 to 55 Degree C).
Model No.	Series-SC1
Storage Temperature	-40 to 176 Degree F (-40 to 80 Degree C).
Brand	DWYER USA
Usage/Application	Industrial processing equipment
Application	Stand alone CO monitoring in parking garage
Isolation	1500 V rms between outputs, input, and power.
Set Points	Adjustable 0 to 100% of span.
Deadband	Adjustable 0.25% to 100% of span.
Dimension	2.95″ H x 0.89″ W x 3.89″ D (75 x 22.5 x 98.5 mm).

Process and Temperature Alarm Switch Module

The Series SC1 Thermocouple Limit/Alarm Switch Modules are on-off or limit switches with selectable process signal. Input type, scale range, output action, and output type are all selectable by the user in the field. All selections are made through easily accessible switches without the need to open the product. Each unit has two form C (SPDT) relays which can operate independently, or be logically connected to operate as a DPDT output. A two color LED indicator indicates the status of each output relay.

These units mount easily on a standard 35 mm DIN rail. Low Voltage (SCLXXXX) units are also available.

Features:

Accepts current, voltage, thermocouple, or RTD inputs
Mounts on standard 35 mm DIN rail
Two color LED indicator to indicate the status of each output relay
Programmable input type, scale range, output action, and output type

Specification:

Power Supply : SC models: 85 to 265 VDC/VAC, 50 to 400 Hz; SCL models: 12 to 24 VDC/VAC, 50 to 400 Hz.
Drift : ±0.02%/°C typical ±0.05%/°C maximum.
Excitation Current : (SC1490) Cu10Ω = 5 mA; Plt 100Ω, Ni 100Ω, Ni 120Ω = 500µA; Plt 500Ω, NiFe 1000Ω = 100 µA; Plt 1000Ω = 50 µA.
Lead Compensation Error : (SC1490) ˜ 0.02%/Ω.
Open Lead Protection : (SC1490) upscale only.
Input Impedance : SC1090: Voltage input = 1 MΩ, current input = 10Ω; SC1290: 3 MΩ.
Sensor Burnout Protection : Selectable.
Relay Output : Form C, SPDT, one per set point, 5A @ 250 VAC, resistive.
Latch Circuit Reset : Automatic at power up. Manual with reset switch on front of module.
Indicators : One dual color LED per set point. Red = relay on, green = relay off.
Wiring Terminals : Screw driven compression type.

Applications:

Stand alone CO monitoring in parking garage
Industrial processing equipment

Other Details:

Model	Description	Power Supply
SC1090	4 to 20 mA, 10 to 50 mA, 0 to 20 mA, 0 to 10 V, -10 to 10 mV	85 to 265 VDC/VAC
SC1290	Thermocouple type J, K, R, S, T, E	85 to 265 VDC/VAC
SC1490	RTD Pt1000 Ni100, Ni120, Cu10, Ni-Fe1000, Ni-Fe2000	85 to 265 VDC/VAC
SCL1090	4 to 20 mA, 10 to 50 mA, 0 to 20 mA, 0 to 10 V, -10 to 10 mV	12 to 24 VDC/VAC
SCL1290	Thermocouple type J, K, R, S, T, E	12 to 24 VDC/VAC
SCL1490	RTD Pt1000 Ni100, Ni120, Cu10, Ni-Fe1000, N-Fe2000	12 to 24 VDC/VAC

Additional Information:

Item Code: Series-SC1

Zener Barrier

Rs 1,700 / Piece

Weight	4.9 oz (140 g).
Power	20 to 35 VDC w.r.t. earth.
Model Number	Series-MTL7706-7787
Brand	DWYER USA
Connection	New
Condition	New
Storage Temperature	-40 to 176 Degree F (-40 to 80 Degree C).
Usage/Application	Electrically isolates pressure and level transmitters from unregulated circuits for intrinsically sa
Safe Area Output	4 to 20 mA.
LED Indicator	Green Power Indication.
Operating Temperature	-4 to 140 Degree F (-20 to 60 Degree C)
Humidity	5 to 95% RH.

Zener Barrier

The MTL7706/7787 is an intrinsically safe (IS) shunt-diode barrier that can be used to communicate with and provide isolations for certain Dwyer® transmitters approved for use in hazardous areas. These barriers limit the amount of energy allowed to pass into the hazardous area, which inhibit ignition in flammable atmospheres.

Features:

Approved for use in hazardous areas

Specification:

Transmitter Voltage : 16.2 V @ 20 mA with 250Ω load (negative w.r.t. earth); 11.0 V @ 20 mA with 500Ω load (negative w.r.t. earth).
Accuracy : ±2 µA under all conditions.
Terminals : Accommodate up to 2.5 mm² stranded or single-core.
Safety Description : 28 µV, 300Ω, 93 mA.

Applications:

Electrically isolates pressure and level transmitters from unregulated circuits for intrinsically safe application

Request
Callback

Additional Information:

Item Code: Series-MTL7706-7787

+(91)-9871034100

07AOSPS8386M1ZM

Battery Powered Temperature Indicator

Rs 2,500 / Piece

Digital Indicating Transmitter

Rs 8,700 / Piece

Indicating Alarm Annunciator

Rs 2,650 / Piece

Miniature Current Switch

Rs 6,400 / Piece

Series SCS Current Switch

Rs 3,250 / Piece

Vibration Transmitter

Rs 24,500 / Piece

Series CCS Current Switch

Rs 1,850 / Piece

Bar Graph Meter

Rs 8,500 / Piece

Digital Timer / Tachometer / Counter

Rs 750 / Piece

Electronic Fan Speed Control

Rs 4,500 / Piece

Ice Cube Relays

Rs 12 / Piece

Low Cost Digital Timer

Rs 6,700 / Piece

Particulate Monitor

Rs 50,000 / Piece

Particulate Sensor

Rs 20,700 / Piece

Particulate Transmitter

Rs 22,000 / Piece

Process Indicator

Rs 5,500 / Piece

Process and Temperature Alarm Switch Module

Rs 6,500 / Piece

Zener Barrier

Rs 1,700 / Piece

admin